Soil Plasticity
In the Soil Plasticity subnode you define the properties for modeling materials exhibiting soil plasticity. This material model can be used together with Linear Elastic Material and Nonlinear Elastic Material. It is available with the Geomechanics Module.
The yield criteria are described in the theory section:
Soil Plasticity
Select a Yield criterion Drucker-Prager, Mohr-Coulomb, Matsuoka-Nakai, or Lade-Duncan. Most values are taken From material. For User defined choices, enter other values or expressions.
Drucker-Prager
In the standard Drucker-Prager formulation, the material parameters are given in terms of the α and k coefficients. Often material data is expressed in the parameters c and used in the Mohr-Coulomb model. You can the choose to use there parameters instead. If so, select the Match to Mohr-Coulomb criterion check box (see Mohr-Coulomb Criterion). If this check box is selected, the default values for Cohesion c and the Angle of internal friction are taken From material.
If required, select the Use dilatation angle in plastic potential check box. If this check box is selected, then enter a value or expression for the Dilatation angle ψ. Alternatively, select From material. The dilatation angle replaces the angle of internal friction when defining the plastic potential.
If the Match to Mohr-Coulomb criterion check box is not selected, then the default Drucker-Prager alpha coefficient and Drucker-Prager k coefficient are taken From material.
If required, select the Include elliptic cap check box. Select from the list the hardening model. When Perfectly plastic (no hardening) is selected, enter values or expressions to define the semi-axes of the ellipse under Elliptic cap parameter pa and Elliptic cap parameter pb. When Isotropic hardening is selected from the list, the default Isotropic hardening modulus Kiso, the Maximum plastic volumetric strain εpvol,max, and the Ellipse aspect ratio R are taken From material (see Elliptic Cap With Hardening). Enter a value or expression to define the initial semi-axis of the ellipse under the Initial location of the cap pb0.
Mohr-Coulomb
The default Angle of internal friction and Cohesion c are taken From material.
If required, select the Use dilatation angle in plastic potential check box. If this check box is selected, then enter a value or expression for the Dilatation angle ψ. Alternatively, select From material. The dilatation angle replaces the angle of internal friction when defining the plastic potential.
Under Plastic potential select either Drucker-Prager matched at compressive meridian, Drucker-Prager matched at tensile meridian, or Associated.
If required, select the Include elliptic cap check box. Select from the list the hardening model. When Perfectly plastic (no hardening) is selected, enter values or expressions to define the semi-axes of the ellipse under Elliptic cap parameter pa and Elliptic cap parameter pb. When Isotropic hardening is selected from the list, the default Isotropic hardening modulus Kiso, the Maximum plastic volumetric strain εpvol,max, and the Ellipse aspect ratio R are taken From material (see Elliptic Cap With Hardening). Enter a value or expression to define the initial semi-axis of the ellipse under the Initial location of the cap pb0.
Matsuoka-Nakai
If required, select the Match to Mohr-Coulomb criterion check box. If this check box is selected, the default Angle of internal friction is taken From material.
If the Match to Mohr-Coulomb criterion check box is not selected, then the default Matsuoka-Nakai mu coefficient μ is taken From material.
Lade-Duncan
If required, select the Match to Mohr-Coulomb criterion check box. If this check box is selected, then enter a value or expression for the Angle of internal friction φ. Alternatively, select From material.
If the Match to Mohr-Coulomb criterion check box is not selected, then the default Lade-Duncan k coefficient k is taken From material.
Tension Cut-Off
This section is only available with the Drucker-Prager and Mohr-Coulomb models
If required, select either None, Mean stress cut-off, or Principal stress cut-off (see Tension Cut-Off).
When Mean stress cut-off is selected from the list, enter a value or expression for the Maximum mean stress σm. Use this to constrain the soil plasticity model with an extra yield surface which limits the maximum pressure in tension.
When Principal stress cut-off is selected from the list, enter a value or expression for the Maximum tensile stress σt. Use this to constrain the soil plasticity model with an extra yield surface, which limits the maximum principal tensile stress.
Deep Excavation: Application Library path Geomechanics_Module/Soil/deep_excavation
Flexible and Smooth Strip Footing on Stratum of Clay: Application Library path Geomechanics_Module/Soil/flexible_footing
Location in User Interface
Context Menus
Ribbon
Physics tab with Linear Elastic Material or Nonlinear Elastic Material node selected in the model tree: