The Electromagnetic Waves, Transient (temw) interface (), found under the Radio Frequency branch () when adding a physics interface, is used to solve a time-domain wave equation for the magnetic vector potential. The sources can be in the form of point dipoles, line currents, or incident fields on boundaries or domains. It is primarily used to model electromagnetic wave propagation in different media and structures when a time-domain solution is required — for example, for nonsinusoidal waveforms or for nonlinear media. Typical applications involve the propagation of electromagnetic pulses.

When this physics interface is added, these default nodes are also added to the Model Builder — Wave Equation, Electric, Perfect Electric Conductor, and Initial Values. Then, from the Physics toolbar, add other nodes that implement, for example, boundary conditions and mass sources. You can also right-click Electromagnetic Waves, Transient to select physics features from the context menu.

Except where indicated, most of the settings are the same as for The Electromagnetic Waves, Frequency Domain Interface.

The physics-controlled mesh is controlled from the Settings window for the Mesh node (if the Sequence type is Physics-controlled mesh). In the table in the Physics-Controlled Mesh section, find the physics interface in the Contributor column and select or clear the check box in the Use column on the same row for enabling (the default) or disabling contributions from the physics interface to the physics-controlled mesh.

When the Use check box for the physics interface is selected, this invokes a parameter for the maximum mesh element size in free space. The physics-controlled mesh automatically scales the maximum mesh element size as the wavelength changes in different dielectric and magnetic regions. If the model is configured by any periodic conditions, identical meshes are generated on each pair of periodic boundaries. Perfectly matched layers are built with a structured mesh, specifically, a swept mesh in 3D and a mapped mesh in 2D.

When the Use check box is selected for the physics interface, in the section for the physics interface below the table, choose one of the four options for the Maximum mesh element size control parameter — User defined (the default), Frequency, or Wavelength. For the option User defined, enter a suitable Maximum element size in free space. For example, 1/5 of the vacuum wavelength or smaller. When Frequency is selected, enter the highest frequency intended to be used during the simulation. The maximum mesh element size in free space is 1/8 in 2D and 1/5 in 3D of the vacuum wavelength for the entered frequency. For the Wavelength option, enter the smallest vacuum wavelength intended to be used during the simulation. The maximum mesh element size in free space is 1/8 in 2D and 1/5 in 3D of the entered wavelength.

When Refine conductive edges is selected, the exterior edges of conductive boundaries, configured by perfect electric conductors, transition boundary, or layered transition boundary conditions, are meshed with a user-specified size. Adjust Angular tolerance (SI unit: rad) to include not only edges on flat surfaces but also curved surfaces. Choose Size type — Relative or User defined. For the option Relative, the mesh size on the selected edges is defined relative to the default maximum mesh size. On the other hand, when the option User defined is selected, the mesh size is set by user-defined value in the Size input field (SI unit: m).

When Add far-field boundary layers is selected, the far-field calculation boundaries adjacent to the selection of scattering boundary conditions or perfectly matched layers create a boundary layer mesh with a thickness of 1/40 to the default maximum mesh size.

The Label is the default physics interface name.

The Name is used primarily as a scope prefix for variables defined by the physics interface. Refer to such physics interface variables in expressions using the pattern <name>.<variable_name>. In order to distinguish between variables belonging to different physics interfaces, the name string must be unique. Only letters, numbers, and underscores (_) are permitted in the Name field. The first character must be a letter.

The default Name (for the first physics interface in the model) is temw.

Select the Electric field components solved for. Select:

The dependent variable (field variable) is for the Magnetic vector potential A. The name can be changed but the names of fields and dependent variables must be unique within a model.

Select the shape order for the Magnetic vector potential dependent variable — Linear, Quadratic (the default), Cubic, Quartic, Quintic, Sextic, or Septic. For more information about the Discretization section, see Settings for the Discretization Sections in the COMSOL Multiphysics Reference Manual.