A Frequency Domain, Modal Reduced-Order Model node () contains settings for a reduced-order model that uses a frequency domain modal method. See Modal Reduced-Order Models.

Click Export Reduced Model () to save the reduced-order model to file as COMSOL Reduced Model file (MPHROM-file). Note that export is only possible if all defined outputs are linear quantities.

The Settings window for a Frequency Domain, Modal, Reduced-Order Model node contains the following sections:

Here you specify whether the reduced-order model should have stateless or stateful interface. Choose Stateless (the default) or Stateful from the Interface list. In the former case, the reduced-order model acts as a black box that uses an internal solver and does not expose its state. In the latter case, the reduced-order model exposes a set of reduced-order equations and state DOFs to the solver used for the calling model, and you can choose whether to solve for the reduced-order model in the same way as for a physics interface.

If you choose Stateless, also specify the Frequency value to be used when evaluating outputs. It is by default set to freq, which means that the reduced-order model will use the same frequency as the calling model in which it is used.

If you choose Stateful, from the Equation form list, choose Study controlled (the default) or Frequency domain. When the setting is Study controlled, the study controls the equation form for the reduced-order model. It then appears as Automatic (Frequency domain), for example, in the Physics and Variables Selection section in the study step’s Settings window. When Frequency domain has been selected, select a source for the Frequency to be used when generating reduced-order equations: From solver (the default) or User defined. When Frequency is User defined, also specify the desired frequency (SI unit: Hz). It is by default set to freq, which means that the reduced-order model will use the same frequency as the calling model in which it is used.

The list in this section contains the reduced-order model input quantities that were set as active in the corresponding Model Reduction node’s Model Control Inputs section when the reduced-order model was created. For each model control input in the Variable column, specify a corresponding Expression to be used when evaluating outputs from the reduced-order model or, when using the stateful interface, when solving reduced-order equations. The default expression is the name of the corresponding reduced-order model input variable. The effect of this is that the reduced-order model will be evaluated for the same value of the input as is seen by the calling model in which it is used. This is usually the desired behavior.

The Modal Reduction solver classifies constraints in the unreduced model when training the reduced-order model according to whether they depend on a reduced-order model input or not. Constraints depending on more than one reduced-order model input are considered an error. Input-dependent constraints are then compared to the constraint modes. If a constraint can be satisfied by a single constraint mode, then that mode is considered to be input-controlled. Constraints that can be satisfied by more than one constraint mode are considered an error during training. Input-controlled modes are treated differently from other modes. There are five columns in the table: Mode, Description, Constrained, Expression, and Variable.

The constraints defined by the settings in the Constraint Modes table are applied in a symmetric way directly on the constraint mode states. This has a few important implications:

This section provides an overview of output quantities that the reduced-order model makes available for evaluation, both during solution and in postprocessing. These outputs are defined in the corresponding Model Reduction node’s Outputs section. The Variable column shows the variable names defined by the reduced-order model.

When Use output dependent variables is selected, the reduced-order model also declares the dependent variable names entered in the Dependent variable column. When the reduced-order model is part of another model, these dependent variables can be assigned the value of the corresponding output variable each time a solution is stored. If the reduced-order model has a stateless interface, this behavior is controlled by the Store output dependent variables setting in the Physics and Variables Selection section of each study step where the reduced-order model is used. If the reduced-order model has a stateful interface, this behavior is controlled by whether the reduced-order model is solved for in a given study step. Apart from the setting to solve for a reduced-order model with a stateful interface, these settings are only available for reduced-order models that have outputs.

This section displays a list of dependent variable fields that this reduced-order model can reconstruct. When the reduced-order model is used in a calling model, it defines an operator <rom_name>.eval(<expr>), where <rom_name> is the Name of the reduced-order model and <expr> is an arbitrary expression.

Use the Load factor to scale the constant part of the right-hand side of the frequency-domain model. This scaling in practice multiplies all loads (source terms) with the specified factor. The load factor does not multiply the right-hand side of any inhomogeneous constraints.

Under Matrices, all matrices that the reduced-model solution includes are listed. The listed vectors and matrices can be accessed using the COMSOL API.