Rigid Connector

The is a boundary condition for modeling rigid regions and kinematic constraints such as prescribed rigid rotations. A rigid connector can connect an arbitrary combination of edges and points which all will move together as being attached to a virtual rigid object.

You can add the node at the boundary, edge, and point levels.

•

When added at the boundary level, you can connect boundaries, edges, and points as long as at least one boundary is selected. Selecting edges and points is optional.

•

When added at the edge level, you can connect edges and points as long as at least one edge is selected. Selecting points is optional.

•

When added at the point level, you can connect a set of points to each other.


	If your selection is too small, you may introduce rigid body motions in the model. No exact rules can be given because there are many possible configurations where, for example, boundaries are connected to each other or affected by other constraints. Also, you can, by providing proper constraints for the rigid connector, suppress rigid body motions. When the rigid connector is added at point level, a set of consistency checks is performed. You can suppress these checks by clearing the Include consistency checks check box in the Advanced section.

If the study step is geometrically nonlinear, the rigid connector takes finite rotations into account.

The feature is similar to the rigid connectors in the Solid Mechanics and Beam interfaces. Rigid connectors from the Shell, Beam, and Solid Mechanics interfaces can be attached to each other.

You can add functionality to the rigid connector through the following subnodes:

•

Applied Force (Rigid Connector) to apply a force in given point.

•

Applied Moment (Rigid Connector) to apply a moment.

•

Mass and Moment of Inertia (Rigid Connector) to add extra mass and moment of inertia in a given point.

Spring Foundation (Rigid Connector) to add a translational or rotational spring or damper in a given point.When physics symbols are shown, a rigid connector is represented by a symbol at the center of rotation, together with a set of lines connecting the center of rotation with the centers of gravity of the selected entities.

•

When the rigid connector is added at the boundary level, such symbols are shown only for the selected boundaries, but not for auxiliary selections of edges or points.

•

When the rigid connector is added at the edge level, such symbols are shown only for the selected edges, but not for auxiliary selections of points.

•

Because of the way physics symbols are evaluated, as a lightweight operation when moving between physics nodes in the model builder tree, it is sometimes not possible to determine the center of rotation. In particular, if an offset is supplied, it will not be taken into account.

Boundary Selection

This section is present when the node has been added at the boundary level. Select one or more boundaries to be part of the rigid region.

Edge Selection

This section is present when the node has been added at the boundary or edge level.

•

When the is added at the edge level, select one or more edges that form part of the rigid region.

•

When the is added at the boundary level, this section is initially collapsed. Here, you can add optional edges to the rigid region. The edges cannot be adjacent to the selected boundaries.

Point Selection

This section is always present.

•

When the is added at the point level, select a number of points that form the rigid region.

•

When the is added at the boundary or edge levels, this section is initially collapsed. Here, you can add optional points to the rigid region. The points cannot be adjacent to the selected boundaries or edges.

Coordinate System Selection

The is selected by default. The list contains any additional coordinate systems that the model includes. Prescribed displacements or rotations are specified along the axes of this coordinate system. It is also used for defining the axis directions of the moment of inertia tensor of the subnode.

Center of Rotation

The center of rotation serves two purposes.

•

If you prescribe the displacement of the rigid connector, this is the place where it is fixed.

•

Results are interpreted with respect to the center of rotation.

Select a — , , or .

•

For the center of rotation is at the geometrical center of the selected edges. The constraints are applied at the center of rotation.

•

For when the main selection is at edge level, select — or . A subnode for selection of the entities is added to the Model Builder. The center of rotation is located at the centroid of the selected entities, which do not need to be related to the edges to which the rigid connector is attached. As a special case, you can select a single point, and thus locate the center of rotation at a certain point.

•

For

When the rigid connector is added at boundary or edge level, select an — or .

When the rigid connector is added at point level, the centroid can only be defined by a point selection.

•

For , in the XC table enter coordinates based on space dimension.

•

For a rigid connector at edge level, when is chosen, a default Center of Rotation: Edge or Center of Rotation: Point subnode is added, depending on the setting of .

•

For a rigid connector at point level, when is chosen, a default Center of Rotation: Point subnode is added.

•

The center of rotation is located at the centroid of the selected entities, which do not need to be related to the rigid connector itself. As a special case, you can select a single point, and thus use that point as center of rotation.

•

When a Center of Rotation: Point node is used for selection, any point in the geometry can be selected, even if it is not part of the physics interface.

Select the check box to add an optional offset vector to the definition of the center of rotation. Enter values for the offset vector Xoffset.

The center of rotation used is the sum of the vector obtained from any of the input methods and the offset vector.

Prescribed Displacement at Center of Rotation

To define a prescribed displacement for each spatial direction x, y, and z select one or all of the and check boxes. Then enter a value or expression for the prescribed displacements u0, v0, or w0.

Prescribed Rotation at Center of Rotation

Select an option from the list — (the default), , or .

•

For select one or more of the and check boxes in order to enforce zero rotation about the corresponding axis in the selected coordinate system.

•

For enter an Ω and an

. The axis of rotation is given in the selected coordinate system.

Reaction Force Settings

Select to compute the reaction force caused by a prescribed motion. The default is to not compute the reaction force. When selected, the prescribed motion is implemented as a weak constraint.

Select to use a unidirectional constraint for enforcing a prescribed motion. The default is that bidirectional constraints are used. This setting is useful in a situation where a bidirectional constraint would give an unwanted coupling in the equations. This would happen if the prescribed value of the motion is a variable solved for in other equations.

Constraint Settings

On the edges where the rigid connector is coupled to a flexible material, all nodes on such an edge are constrained to move as a rigid body. As a default, these constraints are implemented as pointwise constraints. If you want to use a weak constraint formulation, select .

Advanced

It is possible to couple rigid connectors to each other. In the list, you can select any rigid connector defined in the Solid Mechanics or Multibody Dynamics interfaces as being rigidly connected to the current one.


	When coupling rigid connectors to each other, you must be careful not to add conflicting settings. Typically, you should only assign constraints to one of the connectors, and it is recommended to use a common center of rotation. It is, however, possible to deviate from these recommendations and create other meaningful combinations.

When the rigid connector is added at the point level, the section contains the additional check box. The check box, which is checked by default, controls whether to perform singularity checks for the selections. If the checks give false positives, you can turn them off by clearing the check box. This could, for example, be necessary if a rigid connector, which in itself is singular, is connected to another one in a way that forms a stable configuration.

•

You can add a Harmonic Perturbation subnode for specifying a harmonic variation of the values of the prescribed displacements and rotations in a frequency domain analysis of perturbation type.

•

You can activate and deactivate the rigid connector by assigning it to a constraint group. See Load Cases in the Structural Mechanics Modeling chapter.

•

You can assign the value of the prescribed displacement and rotation to a load group. See Load Cases in the Structural Mechanics Modeling chapter.

•

Rigid Connector Theory

•

Harmonic Perturbation

•

Load Cases

Location in User Interface

Context Menus

Ribbon

Physics tab with selected: