Parametric

The node (

) is an attribute node that handles settings for parameter stepping using a parametric solver. This node can be used together with a Stationary Solver node.

There is also an option to run a Stationary study with an , with or without a continuation parameter. When a continuation parameter is selected, the continuation algorithm is run, which assumes that the sought solution is continuous in these parameters. If no continuation parameter is given, a plain sweep is performed where a solution is sought for each value of the parameters. In both cases, a node plus a attribute is used. The parametric solver is the algorithm that is run when a Parametric attribute node is active under a Stationary Solver. Similarly the adaptive solver is the algorithm that is run when an Adaptive Mesh Refinement node is active under a Stationary Solver.


	In order to run a parametric continuation, select the Auxiliary sweep check box under Study Extensions for the Stationary or Frequency Domain study step. Then on the study node’s Settings window, define the parameters in the table and choose one from the Run continuation for list.

•

The Adaptive and Parametric Solver Log

•

The Parametric Solver Algorithm

General

Select an option from the list to specify if the settings are synchronized with the Stationary or Frequency Domain study step, in which case this section does not require any input. The list also displays the same settings made under .


	The continuation algorithm is used if a parameter is selected. Normally the step size, damping, and predictor settings are automatic. If required, you can edit the settings in the Continuation section described next.

To edit the settings, select to modify the sweep type, parameter table, reuse solution from previous step setting, and the parameter to run continuation for. These settings are the same as described in Common Study Step Settings under .

Exactly how the parameter values are used by the solver is determined by the and the option in the section as described below. If more than one parameter name is specified, the lists of parameter values are interpreted as follows. Assume that the parameter names are p1 and p2, and that p1 has the list 1 3 and p2 has the list 2 4:

•

For , the solver first uses p1 equal to 1 and p2 equal to 2. Thereafter, it uses p1 equal to 3 and p2 equal to 4.

•

For , the solver uses this order for the parameter combinations: 1 2, 1 4, 3 2, and 3 4.

To determine what the solver does when there is a solver error or when the continuation backtracking fails, select an option from the list. Select one of the following options:

•

(the default) to stop the parametric sweep and only return solutions before the error.

•

to continue the parametric sweep and store an empty (NaN) solution for this step (or for the remaining continuation).


	Using Store empty solution can be useful if you need to sweep over many different combinations of parameters and it is unknown which ones that will solve. It can also be useful when doing frequency sweeps where frequencies close to resonances fail.

From the list choose (the default) or . When using As specified, the specified order of the parameter values is used. When you use the setting, the parametric solver performs an analysis of the cost of changing the values of involved parameters, and the run order of the parameter values is modified when it is found to be more efficient. If the parameter run order is modified, the modified order is indicated in the window.

Continuation

By default, the solver selects the parameter steps automatically based on the values entered in the field in the section.

Click to select the check box to edit these settings:

•

field to enter a positive number that determines the magnitude of the first parameter step.

•

field to specify a safeguard against too small parameter steps.

•

field to specify an upper bound on the parameter step size. Use this if you suspect that the solver tries to take unnecessarily long steps.

Use the list to control the initial damping factor for the nonlinear solvers for the parameter steps.

•

Select to use the given for the nonlinear solvers for all parameter steps.

•

Select to use the initial damping factor only for the first parameter step.

•

Select (default) to use the initial damping factor only for the first parameter step when the or nonlinear solver method is used in the Fully Coupled solver node and use the initial damping factor in all steps for other solver combinations.

Use the list to control how the initial value for the next parameter value is determined. Select:

•

(the default) to let the parametric solver choose a constant or linear predictor based on the type of stationary solver (a constant predictor for segregated solvers and a linear predictor for fully coupled solvers).

•

to use the solution for the present parameter value as initial guess.

•

to compute the initial guess by following the tangent to the solution curve at the present parameter value.


	This option is overridden, and Constant used instead if you are solving for more than one parameter (that is, when you have entered more than one parameter name in the Parameter name field).

Load Case

This section displays the settings made under for the Stationary study step; it is synchronized with the study settings.

Least-Squares Data


	The section only appears if your license includes the Optimization Module and you are solving a least-squares optimization problem with defined parameters.

Least-squares data are read from file, and the solver sequence is set up accordingly: If there is a least-squares objective containing parameter columns or experimental parameters, a Parametric solver is set up, and the parameter names and values appear under .

Parameter values corresponding to the same parameter names are merged between different files. If is on (which is the default), user-defined parameter values are merged with corresponding merged data from files. For parameters that are defined only in files and not user defined (and vice versa), globally defined values are used.

General parameter values list here refers to the list of parameters in the section above. If is on (which is the default), only least-squares parameter values from files that lie between the smallest and the largest user-defined parameter values are merged. Other values are ignored. Otherwise (that is, is off), all least-squares defined parameter values are merged.

In the case of no user-defined parameters, the merging is done between files only.

If is off, no least-squares parameters from files are used.

You can change the default values of and only if is set to .

Output

Use the list to control at what parameter values the solver stores a solution. Select:

•

to store solutions at the parameter values entered in the field in the section.

•

to store solutions at all parameter values where the solver has computed a solution. This option can generate solutions in-between the values specified by the field in the section if the solver needs to take shorter steps than specified by the values in that field.

Results while Solving

See Results While Solving in the Common Study Step Settings section. Also see Getting Results While Solving.

Cluster Settings

Select the check box to distribute the parameters on several computational nodes. If the problem is too large to run on a single node, you can enable the field to use the nodes’ memory more efficiently. In this case, the same parameter is solved for by several nodes that cooperate as if running a nondistributed sweep. The number of nodes that cooperate is equal to the maximum of the total number of nodes divided by the setting and 1. So if the total number of nodes is 12 and the is 3, then 3 groups with 4 nodes each cooperate.


	Buoyancy Flow of Free Fluids: Application Library path COMSOL_Multiphysics/Fluid_Dynamics/buoyancy_free