The Solid Mechanics Interface

The interface (

), found under the branch (

) when adding a physics interface, is intended for general structural analysis of 3D, 2D, or axisymmetric bodies. In 2D, plane stress or plane strain assumptions can be used. The Solid Mechanics interface is based on solving the equations of motion together with a constitutive model for a solid material. Results such as displacements, stresses, and strains are computed.

The functionality provided by the Solid Mechanics interface depends on the products you are using. The Acoustics Module, MEMS Module, and Structural Mechanics Module add several features, for example geometric nonlinearity and advanced boundary conditions such as contact, follower loads, and nonreflecting boundaries.

The default material is a Linear Elastic Material.

With either the Nonlinear Structural Materials Module or the Geomechanics Module, the physics interface is extended with more materials, for example, material models for plasticity, hyperelasticity, creep, and concrete.


	For a detailed overview of the functionality available in each product, visit http://www.comsol.com/products/specifications/

When this physics interface is added, these default nodes are also added to the — , (a boundary condition where boundaries are free, with no loads or constraints), and . Then, from the toolbar, you can add other nodes that implement, for example, solid mechanics material models, boundary conditions, and loads. You can also right-click to select physics features from the context menu.

Settings

The is the default physics interface name.

The is used primarily as a scope prefix for variables defined by the physics interface. Refer to such physics interface variables in expressions using the pattern <name>.<variable_name>. In order to distinguish between variables belonging to different physics interfaces, the name string must be unique. Only letters, numbers, and underscores (_) are permitted in the field. The first character must be a letter.

The default (for the first physics interface in the model) is solid.

2D Approximation


	From the 2D approximation list, select Plane stress or Plane strain (the default). Plane stress is relevant for structures which are thin in the out-of-plane direction, such as a thin plate. Plane strain is relevant when the 2D model can be considered as a cut through an object that is long in the out-of-plane direction. For more information see the theory section. When modeling using plane stress, the Solid Mechanics interface solves for the out-of-plane strain displacement derivative, , in addition to the displacement field u. When combining Solid Mechanics with other types of physics, there is often an assumption that the out-of-plane extension is infinitely long. This is the case in, for example, Acoustic-Structure interaction problems. In these cases, Plane strain is usually the correct choice.

Thickness


	For 2D components, enter a value or expression for the Thickness d. The default value of 1 m is suitable for plane strain models, where it represents a unit-depth slice, for example. For plane stress models, enter the actual thickness, which should be small compared to the size of the plate for the plane stress assumption to be valid. In Acoustic-Structure Interaction problems, the Thickness should be set to 1 m. Use a Change Thickness node to change thickness in parts of the geometry if necessary.

Structural Transient Behavior

From the list, select (the default) or . Use to treat the elastic behavior as quasi-static (with no mass effects; that is, no second-order time derivatives). Selecting this option gives a more efficient solution for problems where the variation in time is slow when compared to the natural frequencies of the system. The default solver for the time stepping is changed from Generalized alpha to BDF when is selected.

For problems with creep, and sometimes viscoelasticity, the problem can be considered as quasi-static. This is also the case when the time dependence exists only in some other physics, like a transient heat transfer problem causing thermal strains.

Reference Point for Moment Computation

Enter the coordinates for the xref (variable refpnt). The resulting moments (applied or as reactions) are then computed relative to this reference point. During the results and analysis stage, the coordinates can be changed in the section in the result nodes.

Dependent Variables

The physics interface uses the global spatial components of the u as dependent variables. The default names for the components are (u, v, w) in 3D. In 2D the component names are (u, v), and in 2D axisymmetry they are (u, w). You can however not use the ‘missing’ component name in the 2D cases as a parameter or variable name, since it is still used internally.

You can change both the field name and the individual component names. If a new field name coincides with the name of another displacement field, the two fields (and the interfaces that define them) share degrees of freedom and dependent variable component names. You can use this behavior to connect a Solid Mechanics interface to a Shell directly attached to the boundaries of the solid domain, or to another Solid Mechanics interface sharing a common boundary.

A new field name must not coincide with the name of a field of another type (that is, it must contain a displacement field), or with a component name belonging to some other field. Component names must be unique within a model except when two interfaces share a common field name.

Discretization

The default is to use shape functions for the . Using shape functions will give what is sometimes called constant stress elements. Such a formulation will, for many problems, make the model overly stiff, and many elements may be needed for an accurate resolution of the stresses. To display other settings for this section, click the button (

) and select in the dialog box.


	See Table 2-4 for links to common sections and Table 2-5 for common feature nodes. You can also search for information: press F1 to open the Help window or Ctrl+F1 to open the Documentation window.

•

Stresses in a Pulley: Application Library path

•

Eigenvalue Analysis of a Crankshaft: Application Library path