Time Stepping in Transient Models
When solving transient models, first decide on the maximal frequency you want to resolve, say fmax. This frequency translates to a minimal wavelength λmin = c/fmax and in turn to a maximum element size hmax < λmin/5 as discussed in Meshing (Resolving the Waves).
The value of this maximum frequency should also be entered into the Maximum frequency to resolve field in the Transient Solver Settings section at the top physics level. Here it is also possible to select the Time stepping (method) as either Fixed (preferred) or Free. It is recommended to use the Fixed (preferred) method as this method is best suited for wave propagation problems. Using these settings the generated solver will be adequate in most situations if the computational mesh also resolves the frequency content in the model, see Meshing (Resolving the Waves). The auto generated suggestion is good for all linear and weakly nonlinear problems. If the model studied exhibits high nonlinearities the solver may need manual setup and tuning.
The logic for the automatic choice made is as follows. The mesh resolution imposes a restriction on the time-step size Δt taken by the solver. The relationship between mesh size and time-step size is closely related to the CFL number (Ref. 33), which is defined as
where c is the speed of sound and h is the mesh size. This nondimensional number can be interpreted as the fraction of an element the wave travels in a single time step. A CFL number around 1 would correspond to the same resolution in space and time if the discretization errors were of the same size; however, that is normally not the case.
By default, COMSOL Multiphysics uses the implicit second-order accurate method generalized-α to solve transient acoustics problems. In space, the default is 2nd-order Lagrange elements. Generalized-α introduces some numerical damping of high frequencies but much less than the BDF method.
Time Dependent in the COMSOL Multiphysics Reference Manual
The temporal discretization errors for generalized-α are larger than the spatial discretization errors when 2nd-order elements are used in space. The limiting step size, where the errors are of roughly the same size, can be found somewhere at CFL < 0.2. You can get away with a longer time step if the forcing does not make full use of the mesh resolution; that is, if high frequencies are absent from the outset.
When the excitation contains all the frequencies the mesh can resolve, there is no point in using an automatic time-step control which can be provided by the time-dependent solver (the Free option). The tolerances in the automatic error control are difficult to tune when there is weak but important high-frequency content. Instead, you can use your knowledge of the typical mesh size, speed of sound, and CFL number to calculate and prescribe a fixed time step. This is exactly the default behavior when the Fixed (preferred) method is chosen in the Transient Solver Settings section. The Free option corresponds to the automatic time-step control but with some tighter controls of the allowed time-steps. This latter option is still in general not recommended as the fixed time stepping option typically yields much better results (and is faster).
The internal time step generated by the Fixed (preferred) option and the entered Maximal frequency to resolve is set by assuming that the user has generated a mesh that properly resolves the same maximal frequency (minimal wavelength). The following step is generated
Assuming that N is between 5 and 6 and the CFL number is roughly 0.1, these values give a good margin of safety. To check that the accuracy is acceptable, it is recommended that you run a short sequence of typical excitations with progressively smaller time steps (larger fmax) and check the convergence.
If a Multiphysics coupling is used to couple, e.g., acoustics with structural interfaces, the correct time stepping method will be used and it will be based on the settings in the acoustics interface.
When several acoustics interfaces are present in a model, the logic for the time step is to use the minimal time step dictated by the contributing physics.
Some physics, like Electrostatics (present when modeling piezoelectric problems), suggest a BDF time stepping method to be used. If this physics is present, the BDF method will be used but the maximal time steps will be taken from the acoustics suggestions. In this case go to the Time-Dependent Solver node and change the Method in the Time Stepping section to Generalized alpha. All other settings will be correct.
Transient Gaussian Explosion: Application Library path Acoustics_Module/Tutorials/gaussian_explosion