Size Expression

) to specify the size of mesh elements as an expression evaluated on a grid or on a solution. It is possible to add a node both as a global node and as a local node. Free triangular, tetrahedral, and quadrilateral mesh operations that follow below the node in the meshing sequence take the size expression into account.

For some types of adaptation and error estimation in the study settings (using mesh initialization), the adaptive solver add a node to the meshing sequences that represent the adaptive mesh generation, but you can also add a node to set up a mesh size expression of your choice. Right-click a node to add a node from the context menu.


	Only one Size Expression node per meshing sequence is supported.

To add this node as a global node, right-click a node and select . To add this as a subnode, right-click a Mesh Operations node and select . Also see Global vs. Local Attribute Nodes.

Geometric Entity Selection

In this section you define the geometric entities where you want to specify a size expression. Choose the level of the geometry from the list:

•

Choose to specify the size expression for the entire geometry.

•

Choose to specify the domains for the specification of the size expression. Choose from the list to select the domains in the window or choose to select all domains.

•

Choose to specify the boundaries for the specification of the size expression. Choose from the list to select the boundaries in the window or choose to select all boundaries.

•

Choose (3D only) to specify the edges for the specification of the size expression. Choose from the list to select the edges in the window or choose to select all edges. This option is only available in 3D.

•

Choose to specify the points for the specification of the size expression. Choose from the list to select the points in the window or choose to select all points. This option is only available in 2D and 3D.

Element Size Expression

From the list, choose (the default) or to specify whether the evaluation is done on a grid or a solution.

Evaluation on a Grid

Use the field to enter an expression for the absolute element size as a function of x, y, and z (depending on the space dimension). You can also use parameters and global functions, variables, and materials in the expression, but no features from the component are available. The actual size used in a coordinate is the minimum of the specified size expression and the result of the other size parameters (such as the maximum element size and the curvature factor), but this minimum is cut off by the specified minimum element size on a given entity, which acts as a lower bound.

If the expression evaluates to something smaller than the minimum element size, you get a warning that the value was cut off.

To control the grid, you can specify the , which can be , where you specify the number of isotropic cells per dimension in the grid in the field, or , where you specify the side length of a grid cell in the field.

Evaluation on a Solution

From the list, select the solution to use for evaluation.

From the list, select which solution that should be used to evaluate error estimates:

•

Select to use the last solution.

•

Select to use the first solution.

•

Select (the default for Eigenvalue studies) to use all solutions from that study.

•

Select to use a specific solution number that you specify as solution indices in the field.

In the field (only available when is or ), enter weights as a space-separated list of positive (relative) weights so that the error estimate is a weighted sum of the error estimates for the various solutions (eigenmodes). The default value is 1, which means that all the weight is put on the first solution (eigenmode). That is, any omitted weight components are treated as zero weight.

From the list, choose (the default) or .

Error Indicator

If you select , the following settings appear:

The list, where you can add expressions for the error, for example, in terms of the dependent variables (including the variables for error estimation). Use the (

), (), (

)and (

) buttons as needed. If you use several expressions, such as one for each solution component, the error expressions are added to form the sum of all of them. Or right-click a table cell and select , , , or .

In 2D, use the list to control how to refine mesh elements. Select:

•

to make the solver refine only the longest edge of an element.

•

to make the solver refine elements in a regular pattern.

Use the list to specify how the element refinement vector is determined from the error expression. Select:

•

to minimize the L2 norm of the error by refining a fraction of the elements with the largest error in such a way that the total number of elements increases roughly by a factor greater than 1 specified in the accompanying field. The default value is 1.7, which means that the number of elements increases by roughly 70%. The field is an array of h-exponents for the decrease of the error expression. This array has the same indexing as the error expression’s indexing. (for an error expression with two expressions such as errexpr1, errexpr2 and error orders = 2, 3, it means that errexpr1 = O(h2) and errexpr2 = O(h3)). When the adaptation method is used, these numbers are filled in automatically based on the and settings (on the adaptation study). The shape functions can also influence this order. Note that these order numbers need to be positive to generate additional elements (element growth).

•

to refine elements whose local error indicator is larger than a given fraction of the largest local error indicator. Use the accompanying field to specify the fraction. The default value is 0.5, which means that the fraction contains the elements with more than 50% of the largest local error.

•

to refine a given fraction of the elements. Use the accompanying field to specify the fraction. The default value is 0.5, which means that the solver refines about 50% of the elements with the largest local error indicator.

Absolute Size

If you select , the following setting appears:

In the field, type an expression for the element size (in terms of variables defined by the solution).


	The size expression has different interpretation in the grid and the solution case. For the grid case, the spatial variables (x, y, and z, for example) are in the units of the geometry. This means that if your 2D geometry use units km and has a unit square, x and y are both in the range 0 to 1 (km). On the other hand, if you evaluate on a solution, the spatial variables (and any other length dependent variable, such as the local mesh size h), has the units of the component. So using the 2D geometry example above, assuming the component uses the SI unit system, the range of x and y would be 0 to 1000 (m) on the same geometry. Note that in both cases, the evaluated value of the expression is interpreted as a length in the geometry’s unit system.

Smoothing

In this section, you can control the amount of smoothing of the mesh size expression. The (default: 1.4) controls how fast the size field can grow. It is a factor that must be larger than 1.0. Use a higher value to make the mesh coarser closer to areas with a small mesh size, which results in fewer mesh elements.


	Meshing Operations and Attributes